Welcome to IK Tech Corporation
Your one stop for all your satelite needs

Foxcom Platinum IF Band PL7330T [PL7330T1550]/PL7330R10 Link High Power Input, 10dB Optical Budget

Foxcom Platinum IF Band PL7330T [PL7330T1550]/PL7330R10 Link High Power Input, 10dB Optical Budget

Foxcom Platinum IF Band PL7330T [PL7330T1550]/PL7330R10 Link High Power Input, 10dB Optical Budget

IKtechcorp is the distributor for Foxcom Communications Fiber Optic Systems, a leading manufacturer and supplier of commercial satellite equipment. Foxcom offers a wide range fiber links used in the VSAT, DTH, COTM, Teleport, Cable, and Broadcast industries. Satellite, DTH, VSAT, optical, fiber optic, RF.

• IF Band: 10–200 MHz
• More than 25Km distance [40Km with a PL7330T1550]
• Powerful management capabilities via a front panel LCD and rack mounted SNMP
• User control and setting of required IMD level
• Variety of RF and optical connectors
• 1550nm and CWDM ITU grid versions are available for longer fiber runs and single fiber CWDM multiplexing solutions.
Product Code: Foxcom_PL7330R10

Foxcom Platinum IF Band PL7330T [PL7330T1550] / PL7330R10 Link High Power Input, 10dB Optical Budget

Foxcom Platinum IF Band PL7330T [PL7330T1550] / PL7330R10 Link High Power Input, 10dB Optical Budget
 

Summary

Foxcom Platinum IF Band PL7330T [PL7330T1550] / PL7330R10 Link High Power Input, 10dB Optical Budget

Foxcom’s Platinum IF products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With high RF input power and wide dynamic range, the link is designed to provide full specification service up to a full 4 dB optical budget with thePL7330R4 and 10 dB optical budget with the PL7330R10 receiver.

Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability.

In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. 

Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications.

The PL7330T transmitters and PL7330R4/R10 receivers are designed for subrack chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering.

 

     
Order Diagram - Options    
Foxcom Gold Series Order Diagram - Options

Foxcom Platinum IF Band PL7330T [PL7330T1550] / PL7330R10 Link High Power Input, 10dB Optical Budget

 

RF Specifications Units Typical Minumum Maximum
         
Frequency Range - Bandwidth MHz 10 - 200   -
Amplitude Response @any Unity Gain
10 – 200 MHz
any 36 MHz

dB

±0.25
±0.2
.
±0.25
±0.2
Gain Stability dB/24hr ± 0.2   ± 0.25
Gain Variation over temperature dB   -2 2
SFDR1 dB/Hz 103    
SFDR2 dB/Hz 99    
DR (Dynamic Range - single channel)3 dB     30
CNR [any 1 MHz] 2 dB 70 67 73
Noise Figure (NF)1 dB 27   30
Noise Figure (NF)2 dB 13   15
Output IP3 (OIP3)4 dBm - +15 +20
Group Delay Variation- linear @
10 to 30 MHz
30 to 200 MHz
ns
<3.0
<1.0
   
Input/Output Impedance Ohm 50 or 75    
1 dB Compression Point dBm 2   3
Phase Noise5 None      
Third Order InterModulation [IMD]6 dBc   -55 -40
Input Signal Range - Total Power dBm   -30 -5
Maximum Input without Damage       +15
Output Signal Range - Total Power7 dBm   -30 -5
TX/RX Input/Output Return Loss
50 Ohm
75 Ohm
dB
-18
-17
 
-18
-17
Test Port [front panel sample port]8 dB -20 -22 -18
RF Connector
Input/Output
Test Port
Type

F, SMA, BNC, N
F, BNC

         
         
Optical Specifications Units Typical Minimum Maximum
         
Optical Wavelength nm 1310/1550/CWDM    
Optical Power Output mW/dBm 2 / 3 1.7/2.5  
Optical Budget / Distance
10 dB optical budget
dBm/km
1310 nm | 1550 nm
25 | 40
   
RX Optical Input Power dBm
-7

-8
+1
Optical Connector Types Type FC/APC or SC/APC
(E2000 option)
   
Optical Return Loss dB   -60 -55
         
         
Electrical Specifications        
         
Supply Voltage Vdc 12    
Supply Current [TX]9 Amps 0.35    
Supply Current (RX) Amps 0.45    
EMI Rating   EMI Rating: FCC Class B
CE Mark
   
         
         
Physical Specifications        
         
Operating Temperature Range ºC   -10 +55
Storage Temperature Range ºC -45 to +85 -45 +85
Relative Humidity   95% non-condensing    
Altitude ft / Km 10,000 [3.08 ] operating10
14,000 [12.2] non-operating
   
Dimensions [D×W×H] ins/cm 12×0.8×4 / 30.5×2×10.2    
Weight lbs./Kg 0.5 / 0.23    
MTBF Hours TX: 309,481
RX: 359,057
   
MTTR Hours 0.083    
Shock & Vibration  

Designed for normal transportation environment per section MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration.

     

1.   -5 dBm RF input, link gain = 0 dB, IMD=-40 dBc @ 0 dBm optical input - max. RF input
2.   -30 dBm RF input, link gain = 25 dB, IMD=-40 dBc @ 0 dBm optical input - min.. RF input  
3.   User adjustable
4.   -5 dBm RF in @ IMD=-40 dBc
5.   Direct modulation utilized
6.   Adjustable. Above -10 dBm input min. -50 dBc
7.   Alarm trip point: RED -2 dBm, AMBER -33 dBm
8.   -45 dBm minimum input
9.   Under 10º add 120 mA  for TX [laser heating]
10.   WIth standard adiabatic derating at 2ºC/1000ft. [0.3 Km.]