Welcome to IK Tech Corporation
Your one stop for all your satelite needs

Foxcom Platinum Wideband PL7440T/PL7440R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm

Foxcom Platinum Wideband PL7440T/PL7440R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm

Foxcom Platinum Wideband PL7440T/PL7440R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm

IKtechcorp is the distributor for Foxcom Communications Fiber Optic Systems, a leading manufacturer and supplier of commercial satellite equipment. Foxcom offers a wide range fiber links used in the VSAT, DTH, COTM, Teleport, Cable, and Broadcast industries. Satellite, DTH, VSAT, optical, fiber optic, RF.

• Wideband: 10–3000 MHz
• More than 8Km. distance [15Km with the PL7440T1550]
• Powerful management capabilities via a front panel LCD and rack mounted SNMP
• User control and setting of required IMD level
• Variety of RF and optical connectors
• 1550nm and CWDM ITU Grid laser options are available for longer fiber runs and single fiber multiplexing solutions
Product Code: foxcom_PL7440R4

Foxcom Platinum Wideband PL7440T / PL7440R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm

Foxcom PL7440T [PL7440T1550] / PL7440R4 RF Link Wide Power Range, 4dB Optical Budget [8Km - 1310nm & 15Km - 1550nm]
 

Summary

PL7440T [PL7440T1550] / PL7440R4 RF Link Wide Power Range, 4dB Optical Budget [8Km - 1310nm & 15Km - 1550nm]

Foxcom’s Platinum Wideband products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With high RF input power and wide dynamic range, the link is designed to provide full specification service up to a full 4 dB optical budget with thePL7440R4 receiver.

Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability.

In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. TheIMizer requires the use of a correction factor table above 2.5 GHz. 

Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications.

The PL7440T transmitter and PL7440R4 receiver are designed for subrack chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering.

 

     
Order Diagram - Options    
Foxcom Gold Series Order Diagram - Options

Foxcom Platinum Wideband PL7440T / PL7440R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm

 

RF Specifications Units Typical Minimum Maximum
         
Frequency Range - Bandwidth MHz 10 - 3000   3000
Amplitude Response @ Unity Gain
10 - 3000 MHz
any 36 MHz

dB

±2
±0.25
 
±2.25
±0.3
Gain Stability dB/24hr ± 0.2   ± 0.25
Gain Slope1 dB 0 -1.5 +1.5
Gain Variation over temperature dB ± 1.5 -2 2
SFDR2 dB/Hz2/3 100    
SFDR3 dB/Hz2/3 95    
DR (Dynamic Range - single channel)4 dB     50
CNR [any 36 MHz]2 dB 58 55 60
Noise Figure (NF)2 dB 40 37 43
Noise Figure (NF)3 dB 12 10 13
Output IP3 (OIP3)5 dBm 20    
Group Delay Variation- linear
10 to 60 MHz
60 - 3000 MHz
ns
13
1.5
 
-15
-11
Input/Output Impedance Ohm 50 or 75    
1 dB Compression Point dBm 2   3
Phase Noise6 dBm None    
Third Order InterModulation [IMD]4 dBc   -55 -40
Input Signal Range - Total Power7 dBm   -50 0
Maximum Input without Damage dBm     +15
RF Output Signal Range - Total Power
8
9
dBm  
-40
-40

0
0
TX/RX Input/Output Return Loss
50 Ohm
75 Ohm 13
dB
-15
-13
 
-15
-11
Test Port [front panel sample port]10 dB -20 -22 -18
RF Connector Type
Input/Output
Test Port
  F, SMA, N
F, BNC
 
         
         
Optical Specifications  Typical Minimum Maximum
         
Optical Wavelength nm 1310/1550/CWDM    
Optical Power Output mW / dBm 2 / 3 1.7/2.5  
Optical Budget / Distance
4 dB optical budget
dBm/Km 1310 nm | 1550 nm
8 |15
   
RX Optical Input Power dBm -1 -2 4
Optical Connector Types Type FC/APC or SC/APC
(E2000 option)
-  
Optical Return Loss dB   -60 -55
Electrical Specifications        
Supply Voltage Vdc 12    
Supply Current [TX]11 Amps 0.5    
Supply Current (RX) Amps 0.45    
EMI Rating   EMI Rating: FCC Class B
CE Mark
   
         
         
Physical Specifications      
         
Operating Temperature Range ºC   -10 +55
Storage Temperature Range ºC   -45 +85
Relative Humidity   95% non-condensing    
Altitude ft / Km 10,000 [3.08 ] operating12
14,000 [12.2] non-operating
   
Dimensions [D×W×H] ins/cm 12×0.8×4 / 30.5×2×10.2    
Weight lbs./Kg 0.5 / 0.23    
MTBF Hours TX: 309, 481
RX: 359, 057
   
MTTR Hours 0.083    
Shock & Vibration  

Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration.