Welcome to IK Tech Corporation
Your one stop for all your satelite needs

Foxcom GL952CU C-Band Optical Uplink [5,8─6,8 GHz], 3dB Optical Budget

Foxcom GL952CU C-Band Optical Uplink [5,8─6,8 GHz], 3dB Optical Budget

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget

IKtechcorp is the distributor for Foxcom Communications Fiber Optic Systems, a leading manufacturer and supplier of commercial satellite equipment. Foxcom offers a wide range fiber links used in the VSAT, DTH, COTM, Teleport, Cable, and Broadcast industries. Satellite, DTH, VSAT, optical, fiber optic, RF.

• Optimized for Professional Satellite Applications
• Wide Dynamic Range
• 15Km Transmission Distance
• Transmitter and Receiver Gain Control
• Front Panel Test Port
• Powerful Monitoring Features
• Compatible with all 1st Generation Sat-Light Products

Product Code: foxcom_GL952CU

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget
 

Summary

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget

Foxcom's Sat-Light C-Band fiberoptic interfacility links transmit and receive uplink signals in the 5.8─6.8 GHz range between antennas and control rooms or NOCs. Foxcom's IFLs offer a high performance alternative to conventional coaxial-cabled systems, reducing the need for waveguide and minimizing signal attenuation.

The Sat-Light IFLs function as a transparent link, transmitting all satellite modulation formats carrying an entire polarization on each link.

System limitations in using coaxial cable are overcome by the simplicity and performance of fiberoptic connections to provide the highest levels in signal quality. Foxcom achieves this by using state of the art lasers to provide high efficiency, low noise analog links.

A typical C-Band link consists of an optical transmitter that receives the RF signal, transmits it over a single mode fiber to an optical receiver and reconverts the optical signal to RF. Foxcom's advanced fiberoptic technology reduces the attenuation, slope, phase shift, and group delay maintaining extremely low levels over distances of up to 15 kilometers.

The C-Band's link cost effective high performance lasers produce negligible chirp and optical distortion, which is critical for long distance links. The EAM monolithic design, versus connectorized component electro-optics, assures high performance along with excellent reliability. The links are provided with test ports, status and fault LEDs, and gain controls.

 

     
Technical Specifications Diagram    
Inquire

Foxcom GL952CU C-Band Optical Uplink [5.8─6.8 GHz], 3dB Optical Budget

 

RF Specifications Units Typical Minimum Maximum
         
Frequency Range GHz 5.8─6.8    
Link Gain dB Adjustable 0 0
Amplitude Response @ Unity Gain
5.8─6.8 GHz
any 48 MHz
dB
±0.75
±0.25
 
 
Gain Stability @ Constant Temp dB/24hr     ±0.15
SFDR dB/Hz2/3   100  
CNR [36 MHz @ 2.5GHz] dB   45  
Noise Figure (NF) dB   28  
Output IP3 (OIP3) dB   +20  
Third Order InterModulation [IMD]1 dBc Adjustable -50  
Group Delay Variation- linear
3.4─4.2GHz
 
ns 0.4    
Input Signal Range - Total Power dBm   -20 -5
RF Output Signal Range - Total Power dBm   -20 -5
Maximum Input without Damage 60sec dBm   +5  
Input/Output Impedance ohm 50    
TX/RX Input/Output VSWR @ 50 Ohm dB   1.5:1  
RF Connector Type
Input/Output
Test Port
  SMA
SMA
   
Test Port [front panel sample port] dB -20 -19 -21
         
         
Optical Specifications Unit Typical Minimum Maximum
         
Optical Power Output dBm   -3 0
Optical Budget / Distance
3 dB optical budget
dB/Km

 15Km @ 1550nm

   
Optical Connector Types   FC/APC    

Optical Wavelength

nm

1550/CWDM

   
         
         
Electrical Specification        
         
Supply Voltage Vdc 13 12.7 18
Supply Current [TX] Amps 0.8    
Supply Current (RX) Amps 0.5    
         
         
Physical Specifications        
         
Operating Temperature Range     -10 +55
Dimensions [D×W×H]  

RX: 5” x 5” x 1.5”

TX: 5” x 5” x 3”